Month: September 2019

It’s been some time since I’ve posted anything here.  Mostly because it felt not much of significance has been going on, but there actually was.  My list of things to accomplish is shrinking steadily.

For many years, I’ve wanted to change the color of the primary rooms in the house.  It was formerly a yellow color and it was everywhere.  Because it was everywhere it was too much for me to commit to doing.  I eventually hired someone to do the job for me.  At the same time, I hired someone to remove the popcorn ceiling in the space, which was another too-big-to-tackle task.

Popcorn down; ready for painting.

Painting complete; area rug added.  I also added an area rug in the music room, as much for appearance as for reducing the echo and reflections.

After that was complete, I replaced the smoke detectors, which had turned yellow on their own, with fresh new white ones.  I also shot the doorbell cover with fresh white paint.  So everything on the walls was fresh and new.

And I finally – finally – got the artwork up on the wall like I’ve wanted for years.

So many years ago, I began a project of repainting the folding closet doors in the bedrooms and the pantry.  My painting turned out really crappy for some reason, so I sort of abandoned the idea.  The closet doors went back in place, but the pantry door, with its crappy paint job, just sat in the garage.  I recently decided to slap on another coat of paint on it, using some leftover paint from other projects and it turned out decently.  So, I was able to finally return the pantry doors to their place.  Some of the mistakes I made in that project were with the rollers and pivot pin that holds the door in place.  First, I installed the pieces on the door upside down.  I couldn’t figure out how the door had suddenly reversed sides.  After realizing that mistake, I was unable to remove the rollers without breaking one.  So back to Lowes for a replacement.  Installing the replacement, the new piece wouldn’t fit in the hole, despite the hole being the correct 3/4” size.  I hammered in the roller, but just broke it.  So I drilled out the broken roller and used a razor to trim the next roller sleeve to slide into the hole easier.  Success at last.  Part of the folding door repainting project was going to be replacement of the hinges, which were brass and had been painted over previously.  I do have the nickel hinges available, so I may do some swapping out on the other doors in time.

A lot of this work has been done in order to clear out the garage in preparation for the garage door installation.  Things that were previously stored in the garage are now stored in closets in the bedrooms.  The folding doors are now out of the garage.  Along the way, I found the dart board that had been installed in the garage when it was a game room.  On a whim, I decided to remount it, which will now necessitate installation of a light and the purchase of some darts.  (I am disappointed I can’t find the darts that used to be here.)

One of the bigger space hogs in the garage is the leftover paint cans from all these projects.  I had seen something online about storing paint in mason jars so you could see the colors and take up less space in the process.  I liked the concept, so after years of procrastination, I bought the mason jars and transferred the paint to them, using my label maker to document the paint color and finish.  In many cases, I had two jars of each color, so half a gallon of extra paint – more than enough for touching up.  All of these quart jars went on the floor in the pantry, which is now behind a closed door.  There are some unopened gallon cans of paint and primer than I’m probably going to keep in the garage somewhere on a shelf.  Otherwise, if it’s opened, it should be in a mason jar.

In my office, which is now on the lanai, things were rather messy.  I had a couple of plastic bin drawer units that held all my cables, and I had a lot of cables.  It was always a hassle if you wanted to find anything.  I took the opportunity one weekend day to relocate all the cables from the six plastic drawers to an unused storage cube unit, which had a bunch of pull-out fabric cubes with labels.  I broke up all the cables into the different types, gave each their own cube and labeled the cubes accordingly.  That freed up space in my office and moved the clutter to a bedroom closet, even though it wasn’t clutter anymore.  I still have room to work in both bedroom closets, so I need to determine what is going to be stored in each.

Outside, I had to refresh my floodlight bulbs.  I had a couple of broken and burnt out bulbs, that I wanted to convert to LED.  Along the way, I made a discovery.  Early on when I bought the house, I installed a dusk-to-dawn light at the driveway corner.

This light was on a switch near the main entryway and always just remained switched on, so the light could turn on and off with the sunset.  What I didn’t know, was that the switch also controlled the lights on the other side of the house.  While I was replacing the bulbs, I learned that both bulbs on this fixture were burnt out, and why wouldn’t they be?  They’d been switched on for over a decade.

The problem was now, if I replace the bulbs, the light will shine all day and night.  If I turn off the switch, I lose the dusk to dawn light.  So I decided to swap the fixture with a motion-sensing version.  For the most part, the lights would stay off unless someone walked nearby.  So, sometimes at night, I will see a burst of light come in through my bedroom windows where the motion sensor light is pointing.  It’s fine.

I designated Sunday to be the day I would change out my kitchen sink.  It was actually more than just the sink.  It was also adding an instant hot water tank and an under-sink water filtration system.  This project has been a long time coming.  I bought the sink back in April and most of the other parts a month or so later.  But everything sat in the garage waiting for the right time.  In July, I had an electrician install an outlet for the water heater, but still, the time wasn’t right yet.  The sink was just sitting in the garage waiting for install.

With the upcoming garage door install, a renewed interest in clearing out the garage started, and part of that was clearing out that sink and the components.  I planned to do it on Sunday, initially budgeting a couple of hours.  Judging from my initial budget of a couple of hours, I then budgeted the whole day.  By Sunday’s end, I wondered why I didn’t start this on Saturday.

The process got off to a bad start right away.  Simply turning off the water under the sink was troublesome.  After a decade of never being turned, the shutoff valves were frozen and stiff from years of mineral deposits (the house has ridiculous calcium in the water).  Freeing them up introduced some minor leaks, so I had to shut the water off at the hot water tank.

Removal of the old garbage disposal and sink wasn’t too difficult.  Having the sink removed afforded an opportunity for cleaning, which is something that happens every once in a while, where I find inexplicable messes dating back to the previous homeowners.  As soon as possible, I dry-fit the new sink in place and was relieved it fit without any issues.  The last time I looked at my watch it was 10:30 and now all of a sudden, it was after noon.  I took a break for lunch.

Returning from lunch, I decided to plan the placement of the water filter and hot water tank.  This turned out to be harder than originally thought.  To plan properly, I needed to have the garbage disposal in place to see what room would be left over.  So I had to install the drains in the sink.  I had hoped to have the drains installed long ago, before even thinking about the sink install, but that never really happened.  Instead, I made a quick run to Ace Hardware to get plumbers putty, as well as a couple of fittings that I didn’t realize were not included in the hot water kit.

There’s not a lot of room under the sink and with the water pipes, drain pipe, and garbage disposal all in the way, my install options were highly limited.  I originally wanted the hot water on the right side and the filtered water tap on the left, but that was reversed out of space requirements.  I mounted the components on the walls and checked the clearance of everything with the sink back in place.  So far, so good.  While the sink was out and I had access to everything, I installed all the water taps for the new devices.  I wasn’t overly pleased that I couldn’t route the filtered water into the hot water tank.  The filtered water had a plastic water line in from the water supply and out to the faucet.  The hot water tank had a copper pipe from the water supply.  So, two taps were needed (one was not included with the install kit).

Next was to pre-install the faucets and taps on the new sink before I dropped it in.  This was fairly uneventful except for some confusion on how the washers and gaskets worked on the filtered water tap.  As I secured the pieces, I was highly impressed with the sturdiness of the sink material.  There was no flex like on the old sink.  Once everything was attached, it was time to commit the sink to the counter.  I laid down a line of caulk around the whole opening and dropped the sink in.  There was a lot of excess caulk to clean up, which was messy as hell.  I didn’t have any running water there to clean any of it up, so it was a back and forth trip between the laundry room sink with water, and a whole lot of paper towels.  There’s underside clips that need to be installed on the sink and because of the unreasonably tight clearance at the front of the sink, I only installed clips on the left, right and rear of the sink.  I’m sure it will be fine.

I’m still ignoring the minor leaks in the supply valves because I need to focus on the drain pipes.  I reused the gross old pipes from the previous sink (with some slight washing), but because of the new sink’s greater depth, nothing fit anymore.  Everything was a inch or so lower than the outlet pipe.  This was, at this hour, devastating.  I really didn’t know what the corrective course would be, because I didn’t know what pipes were available for me to purchase.  I took a few pictures of the pipes in their mismatched positions, bagged up some of the pipes and headed to Lowes.  It’s 7:00 now and they close in an hour.  If I don’t figure something out, I’m done for the day.

Staring at dozens of potential options, I didn’t see exactly what I wanted.  As best I could determine, I needed a drain pipe that had a right angle and dropped an inch or so after the bend.  There’s no such thing.  One pipe caught me eye, which was a replacement drain pipe for the garbage disposal.  The illustration showed a straight pipe out of the disposal.  I didn’t know that was an option.  The disposal arrives with an L pipe.  So, if I replace the disposal drain pipe with a straight pipe, that raises everything up significantly.  But, that also means I have to extend the pipe after the T valve.  This is going to be my best bet, so I bought the straight pipe and two extension pipes (one extra in case of screwups).

Back home now, I struggle to piece everything together like some sort of puzzle game.  I had to shorten a couple of pipes to make them fit, and along the way, I had some really tight fittings that leaked until I could balance the pressure in different areas.  But I did get a leak-free drain test around 9:00.  That was as good a time as any to give up for the night.  The kitchen was a disaster with tools and rags and packing materials and undersink cleaning bottles all over the floor and counters.  And despite what seems like success, I still hadn’t addressed the leaking supply valves.  Aside from the obviousness that you can’t have leaks under a sink, I couldn’t have leaks on those valves because the hot water heater was installed underneath them and a leak would simply short out and ruin my expensive purchase.

I still had Sunday garbage to take out and I was sore.  Very sore.  Lots of cramping myself under the sink and getting up and down over and over again.  I also left the hot water shut off for the night.  I would have to open it back up first thing in the morning before showering, then close it again before leaving for the day.

The next day, I re-evaluated the leaks.  The one was easily fixed with some teflon tape.  The other required another trip to Lowes to buy a new brass washer for the inner assembly.  Of course you can’t just buy a washer (that I could find).  I bought a repair kit that had a bunch of rubber and metal washers and screws and o-rings.  All for one washer.  In the end, though, that fixed the leak.

I reinstalled the hot water tank and tested all the connections.  No leaks coming in or out.  I turned the water and electric back on and I had a fully operational sink.  And just to be absolutely safe, I placed a leak detector under the sink, so if it does start leaking at any time, I’ll get a 120db notification.